Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Which of the following is valid for Single-area OSPF design type? (Choose two) A. Using summarization results in smaller routing tables B. A better solution for efficient routing C. Every router is required to process many link-state advertisements (LSAs) D. Larger routing tables are required https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/multiarea-ospf-planning.html Which translation option would most likely be used in your home to connect all your devices to the Internet over your DSL, Cable, or Fibre connection? A. Dynamic NAT with overloading B. Dynamic NAT C. PAT D. Static NAT You want to create an access list on R2 to permit traffic from VLAN 10 to access the Internet using HTTP. VLAN 10 has been configured to use the 10.1.1.0/26 subnet. Which commands can you use? (Choose three) A. ip access-list WEB_TRAFFIC B. permit tcp 10.1.1.0 0.0.0.63 any eq 80 C. access-group WEB_TRAFFIC out D. permit tcp 10.1.1.64 0.0.0.63 any eq 80 E. permit tcp 10.1.1.0 0.0.0.31 any eq 80 Which command could you enter to encrypt passwords? A. enable secret B. username {username} secret {password} C. service password-encryption D. All of the above E. None of the above Which of the following commands is used to indicate the real true speed of the interface? A. no shutdown B. interface serial C. show controllers D. clockrate E. bandwidth https://www.learncisco.net/courses/icnd-2/wan-technologies/serial-encapsulation.html During a maintenance window, you make some changes to R2. You document these changes in your configuration management system. Later that night, you are called in to fix an issue that requires you to make additional changes to R2. The next morning your co-worker addresses another issue but this time on R1. All of these changes are documented properly but neither you or nor your coworker discuss the changes. These changes stay implemented for months. What is this best described as? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring What will the solicited node multicast address be for the IPv6 address 2001:DB8:1001:F:2C0:10FF:FE17:FC0F? A. FF02:0000:0000:0000:0000:10FF:FE17:FC0F B. FF02:0000:0000:0000:0000:0001:FF17:FC0F C. 2001:0000:0000:0000:0000:0001:FF17:FC0F D. FF02:0000:0000:0000:0000:0001:FE17:FC0F Which of the following behaviors is applied to a low latency queue in a Cisco router or switch? (Choose two) A. Congestion management B. Shaping C. Policing D. Priority scheduling E. Round robin scheduling If you want to be alerted when a device configuration differs from the intended configuration, what should you implement? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring An enterprise plans to start using a public cloud service, and is considering different WAN options. The answers list four options under consideration. Which one option has the most issues if the company chooses one cloud provider but then later wants to change to use a different cloud provider instead? A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN Which end-to-end connectivity troubleshooting tool displays and modifies entries stored as IP addresses and their resolved MAC addresses? A. Ping B. Telnet C. Address Resolution Protocol, or ARP D. Traceroute https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/troubleshooting-connectivity.html Which of the following commands displays the OSPFv3 neighbors, the neighbor router ID, and the interface it is available through? A. show ipv6 ospf neighbor B. show ipv6 ospf C. show ipv6 route ospf D. show ipv6 ospf interface https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/ospfv3-configuration.html What is required for a directly connected route to be added to the routing table? (Choose two) A. The network command must be issued under the routing process B. BGP must be running on the router C. A local route must be manually created D. The IP route command must be configured in global configuration mode E. Configure an IP address on the interface F. The interface Status must be up and the Protocol must be up What commands would you need to configure to enable DHCP Snooping so that PC4 couldn’t become a rogue DHCP server? A. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/12, ip dhcp snooping trust B. Configure the following on SW 1: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/24, ip dhcp snooping trust C. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/24, ip dhcp snooping trust D. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/24, ip dhcp snooping trust E. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/12, ip dhcp snooping trust F. Configure the following on SW 1: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/24, ip dhcp snooping trust Consider the following scenario: Host A has IP address 192.168.6.3 and MAC address 0800:0111:3333. Host B has IP address 192.168.7.3 and MAC address 0800:0222:4444. The router has IP address 192.168.7.1 and MAC address 0800:0444:1111. When Host B receives a packet from Host A, the frame contains the source and destination IP and MAC addresses. What should be the source MAC address? A. 0800:0444:1111 B. 192.168.7.3 C. 192.168.6.3 D. 0800:0222:4444 https://www.learncisco.net/courses/icnd-1/lan-connections/packet-delivery-process-at-l3.html How many IPv4 ACLs can you apply to a router interface? A. Four, two inbound and two outbound B. Two, one inbound and one outbound C. As many as you need, inbound or outbound D. Only one, inbound or outbound A queuing system has three queues serviced with round robin scheduling and one low latency queue that holds all voice traffic. Round robin queue 1 holds predominantly UDP traffic, while round robin queues 2 and 3 hold predominantly TCP traffic. The packets in each queue happen to have a variety of DSCP markings per the QoS design. In which queues would it make sense to use a congestion avoidance (drop management) tool? (Choose two) A. The LLQ B. Queue 1 C. Queue 2 D. Queue 3 If the subnet mask is 255.255.255.0, what is the wildcard mask? A. 0.0.0.0 B. 0.0.0.255 C. 0.0.0.254 D. 255.255.255.0 https://www.learncisco.net/courses/icnd-1/acls-and-nat/acl-wildcard-masking.html Which command can be used to find the default gateway address on a Windows PC? A. show ipv6 route B. ping C. netsh D. ipconfig Which QoS feature is typically used inbound to a network to limit the amount of traffic that is allowed to flow in? A. Traffic classification B. Traffic shaping C. Traffic limiting D. Traffic policing Which statements best describe physical and logical topologies? (Choose two) A. The physical topology requires that data takes the shortest path across the network towards its destination B. The physical topology is dependent on the type of cabling that is used C. The logical topology can allow data to take a longer path across the network towards its destination D. The primary categories of logical topologies are bus, star, and mesh https://www.learncisco.net/courses/icnd-1/building-a-network/the-functions-of-networking.html When planning a greenfield SDA design, what traditional LAN design points should be included? (Choose two) A. The number of switchports needed in each switch B. The required speed of the switchports C. A security firewall to properly segment traffic D. The Spanning Tree mode of operation to use Which cloud service model gives a customer complete control over the virtual hardware components, including processor performance, network connectivity, how much memory and storage space is required, and potentially the operating system that is preinstalled? A. SaaS B. IaaS C. PaaS D. TaaS A user is experiencing a loss of end-to-end connectivity in an IPv4 network. You have verified that the name resolution entry is correct. Now you want to check whether any IP ACLs are set on the interface. Which command should you use to do so? A. show ip access-list B. show traceroute C. show ip route D. show ip interfaces https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/acl-issues.html Which layer of the OSI model defines how data is formatted for transmission? A. Session B. Network C. Transport D. Application E. Data-link F. Presentation https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html What are some of the wireless LAN controller (WLC) capabilities? A. Security management B. Dynamic RF management to assign channels to APs C. RF monitoring to gather information about the channel D. Ease of deployment by programming all RF policies and wireless LAN policies on all APs E. All of these are correct. Which two of these are characteristics of the 802.1Q protocol? (Choose two) A. It is used exclusively for tagging VLAN frames and does not address network reconvergence following switched network topology changes. B. It modifies the 802.3 frame header, and thus requires that the FCS be recomputed. C. It is a Layer 2 messaging protocol which maintains VLAN configurations across networks. D. It includes an 8-bit field which specifies the priority of a frame. E. It is a trunking protocol capable of carrying untagged frames. https://www.learncisco.net/courses/ccna/part-5-virtual-lans-vlans/vlans-review.html Which DSCP marking group was created to be backward compatible with Internet Protocol Precedence (IPP) values? A. EF B. AF C. CS D. PF Refer to the diagram. What is the name of the device (referenced with the arrow) that communicates with wireless clients? A. Wireless controller B. Access point C. Router D. Wireless bridge Review the topology diagram. Network 10.123.0.0/24 is the backbone area. Network 10.12.0.0/24 is area 1, and network 10.34.0.0/29 is in area 2. Which of the following are true? (Choose three) A. R1 is a backbone router. B. R1 is an ABR. C. R1 is an internal router. D. R3 would see the OSPF network of 10.12.0.0/24 as an intra-area route. E. R1 and R3 would have the same LSA information about the backbone area. You are implementing IPv6 stateless address autoconfiguration for your end stations. What must be the prefix of the IPv6 network in order for the clients to autoconfigure their addresses? A. /48 B. /56 C. /64 D. /96 E. /32 It is typical for server processors to utilize a technique that allows each physical processing core to be split into a number of virtual cores; this is commonly referred to as __________. A. processor virtualization B. multi-threading C. virtual processing D. processor switching Which of the following parameters are necessary when creating a new WLAN with the controller GUI? (Choose two) A. SSID B. VLAN number C. Interface D. BSSID E. IP subnet Refer to the diagram. What is the name of the device referenced with the arrow, assuming the traffic coming from the wireless clients followed the dashed path? A. Autonomous AP B. Lightweight AP C. Wireless controller D. Wireless router Which command displays information about security options configured on an interface? A. show port-security interface [interface-id] B. show port-security [interface-id] C. show port-security[address] D. show security [interface-id] Using the exhibit as a reference, what is a valid key? A. ”lastUpdateTime”: 1572317520439 B. ”CSR1000V” C. ”role” D. ”platformId”: Which Cisco IOS command is used to advertise a default route into an OSPF domain regardless of whether a default static route is configured? A. default-information originate B. default-information originate always C. default-information originate permanent D. default-information originate no-check Refer to the exhibit. Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q-compliant trunk to another switch. Based on the output shown, what is the reason the trunk does not form, even though the proper cabling has been attached? A. VLANs have not been created yet. B. An IP address must be configured for the port. C. The port is currently configured for access mode. D. The correct encapsulation type has not been configured. E. The "no shutdown" command has not been entered for the port. Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2? A. This switch has more than one interface connected to the root network segment in VLAN 2. B. This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree. C. This switch interface has a higher path cost to the root bridge than another in the topology. D. This switch has a lower bridge ID for VLAN 2 than the elected designated switch. Which IPv6 header field specifies the maximum number of hops that an IPv6 packet can take? A. Flow label B. Time to live C. Next header D. Hop limit E. Traffic class F. Extension header The show port-security interface f0/1 command lists a port status of Secure-shutdown. Which of the following answer must be true about this interface at this time? A. The show interface status command lists the interface status as connected. B. The show interface status command lists the interface status as err-disabled. C. The show port-security interface command could list a mode of shutdown or restrict, but not protect. D. The show port-security interface command could list a violation counter value of 10. Identify the commands required to verify both - the IP addresses of a switch and a host. (Choose two) A. show interface status B. show ip interface brief C. ipconfig /renew D. ipconfig /release E. ipconfig /all https://www.learncisco.net/courses/icnd-1/lan-connections/starting-a-router.html Which of the following components contains the running copy of the configuration file? A. Interface B. ROM C. Flash D. RAM E. CPU F. NVRAM https://www.learncisco.net/courses/icnd-2/network-management/router-internal-components-overview.html Refer to the exhibit; in which area would R1’s Gi0/0 interface be placed? A. 5 B. 6 C. 10 D. 11 Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two) A. The transport layer divides a data stream into segments and may add reliability and flow control information. B. The data link layer adds physical source and destination addresses and an FCS to the segment. C. Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information. D. Packets are created when the network layer adds Layer 3 addresses and control information to a segment. E. The presentation layer translates bits into voltages for transmission across the physical link. https://www.learncisco.net/courses/ccna/part-1-internetworking/data-encapsulation.html In what security zone are the public web servers located? A. DMZ B. Inside C. Outside D. Campus Which options are available for obtaining a license file? (Choose two) A. Cisco Registration Manager B. Cisco License Manager C. Cisco Portal D. Cisco PAK E. Cisco License Registration Portal F. Cisco Manager Which statements describe network characteristics? (Choose three) A. Cost represents the general price of components, installation, and maintenance of the network B. Reliability indicates how protected the network is, including the information that is transmitted over the network C. Topology is a measure of the data rate in bits per second of a given link in the network D. Security depicts the structure of the network E. Scalability indicates how well the network can accommodate more users or data transmission requirements F. Availability is the probability of the network being available for use when required https://www.learncisco.net/courses/icnd-1/building-a-network/the-functions-of-networking.html What are some perceived benefits of controller-based networks as compared to traditional networks? (Choose two) A. New operational models that allow for a single device to be instantiated with the entire network in mind B. The use of APIs to mass-configure network devices, allowing for more consistency and fewer errors C. The use of DevOps approaches in the network to increase efficiency and productivity D. The use of legacy approaches in the network to increase efficiency and productivity Which two commands can be used to verify a trunk link configuration status on a given Cisco switch interface? (Choose two) A. show interface trunk B. show interface interface C. show ip interface brief D. show interface vlan E. show interface switchport https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/troubleshooting-switched-network.html Which of the following describes a Private IPv6 address? A. ::1 B. Starts with FE80::/10 C. Represented by :: D. Starts with 2000::/3 https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/ipv6-unicast-addresses.html You need to create an ACL entry that will only permit all addresses in the 10.1.1.16/28 network. Which address and wildcard mask combination will accomplish this for us? A. 10.1.1.16 0.0.0.31 B. 10.1.1.16 0.0.0.63 C. 10.1.1.16 0.0.0.255 D. 10.1.1.16 0.0.0.15 E. 10.1.1.16 0.0.0.3 F. 10.1.1.16 0.0.0.7 Imagine you configured OSPFv2 in a small lab network. Which of the following answers list a condition that could keep the routers in your lab from learning all the routes to all the IPv4 routes in your small lab network? (Choose two) A. An ACL could be blocking router advertisements. B. Two neighboring routers that connect to the same link have been configured with the same OSPF area and with the same IPv4 subnet mask. C. Any physical layer problem that would prevent two neighboring routers from being able to ping each others IPv4 addresses in the subnet that exists between the two routers. D. Two neighboring routers that connect to the same link have been configured with the same OSPF process ID on the router ospf command. All of the switches in your VTP domain are operating as servers. Which command changes the operation mode of DSW2 to client? A. vlan client B. show vlan brief C. vtp password client D. vtp mode client Which command is used to create a standard numbered IPv4 ACL? A. access-list numbered B. ip access-list C. numbered access-list D. access-list ip E. access-list

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources