Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
What is the name of the protocol that has been developed by the ONF that is used to communicate between an SDN controller and the network devices it controls? A. OpFlex B. OpenSDN C. SbControl D. OpenFlow Which of these are QoS requirements when designing a Cisco voice network? (Choose two) A. Jitter < 30 ms B. Loss < 1% C. One-way delay < 200 ms D. Jitter < 50 ms E. Loss < 2% F. Round-trip delay < 200 ms Which statement about VLAN operation on Cisco Catalyst switches is true? A. When a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source MAC address and the MAC address table. B. Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN. C. Broadcast and multicast frames are retransmitted to ports that are configured on different VLAN. D. Ports between switches should be configured in access mode so that VLANs can span across the ports. https://www.learncisco.net/courses/icnd-1/ethernet-lans/developing-design-for-layer-2.html Which of the following cloud services is most likely to be used for software development? A. IaaS B. PaaS C. SaaS D. SLBaaS Using the exhibit as a reference, how many JSON objects are there? A. 11 B. 1 C. 2 D. 12 Which of the following protocols are used to auto negotiate trunk formation between two switches? A. CDP B. VTP C. DTP D. STP R1, R2, R3, and R4 have their Fast Ethernet 0/0 interfaces attached to the same VLAN. A network engineer has typed a configuration for each router by using a word processor. He will later copy and paste the configuration into the routers. Examine the following exhibit, which lists configuration for the four routers, as typed by the network engineer. Assuming that all four routers can ping each other’s LAN IP addresses after the configuration has been applied, choose the routers that will be able to form a neighbor relationship with the other routers on the LAN. (You can assume that, if not shown in the exhibit, all other related parameters are still set to their defaults.) (Choose two) A. R1 B. R2 C. R3 D. R4 E. None of the routers will exchange routing information. Refer to the exhibit. What will Router1 do when it receives the data frame shown? (Choose three) A. Router1 will strip off the source MAC address and replace it with the MAC address 0000.0c36.6965. B. Router1 will strip off the source IP address and replace it with the IP address 192.168.40.1. C. Router1 will strip off the destination MAC address and replace it with the MAC address 0000.0c07.4320. D. Router1 will strip off the destination IP address and replace it with the IP address of 192.168.40.1. E. Router1 will forward the data packet out interface FastEthernet0/1. F. Router1 will forward the data packet out interface FastEthernet0/2. You are configuring HSRP for VLAN 10. You want its primary default gateway to be R1 and secondary default gateway be R2. What should you consider when configuring HSRP for R1? (Choose two) A. Ensure that you use the same group number for all your configuration commands B. Ensure that pre-emption is disabled C. To ensure R1 always has priority, use the IP address of the physical interface of R1 for the virtual IP address D. Ensure that you specify R2 has a lower priority than R1 Which route type in the routing table identifies the networks that are attached to the local router? A. Static route B. Directly connected route C. Dynamic route D. Local route E. Default route In a network that uses OSPF, you need to configure a default route to 203.0.113.1 on one router that will then be advertised to the other routers. What command should be used first? A. ip route 203.0.113.1 0.0.0.0 203.0.113.1 B. ip route 0.0.0.0 0.0.0.0 203.0.113.1 C. default ip route 0.0.0.0 0.0.0.0 203.0.113.1 D. ip route 203.0.113.1 0.0.0.0 0.0.0.0 Which of the following four TCP/IP layers represents the core of the TCP/IP architecture? A. Network Access B. Transport C. Internet D. Application https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html Refer to the exhibit. Which switch provides the spanning-tree designated port role for the network segment that services the printers? A. Switch1 B. Switch2 C. Switch3 D. Switch4 What type of variable is being shown? Routers = [R1,R2,R3] A. List B. Dictionary C. Simple D. Unsigned integers Which command is used to verify your OSPFv3 neighbor adjacencies? A. show ospf neighbor B. show ipv6 brief C. show ipv6 ospf D. show ipv6 ospf neighbor Which of the following behaviors are applied to a low latency queue in a Cisco router or switch? (Choose two) A. Shaping B. Policing C. Priority scheduling D. Round-robin scheduling You are configuring static NAT on a Cisco IOS router that is connected to your ISP. You goal is to have the private IP of 10.1.1.10 translated to 203.0.113.5. Which command must be issued on the interface connected to the service provider? A. ip nat pool NAT_POOL 203.0.113.5 B. ip nat inside C. ip nat outside D. ip nat inside source static 10.1.1.10 203.0.113.5 What command should you configure globally to enable a 15-minute recovery time for the port security errdisable state? A. errdisable recovery interval 15 B. errdisable recovery timer 15 C. errdisable recovery timer 900 D. errdisable recovery interval 900 You need to configure your 2960 Catalyst switch to automatically recover a port within one minute that has been placed in the err-disabled state because too many MAC addresses were learned on an interface. Which commands will accomplish this for you? (Choose two) A. errdisable recovery cause psecure-violation B. errdisable recovery interval 10 C. errdisable recovery cause bpduguard D. errdisable recovery interval 60 E. errdisable recovery interval 1 F. errdisable recovery cause security-violation A MAC address table can store a number of address entries. However, sometimes conditions can cause the MAC address table to be empty. Identify these conditions. (Choose three) A. The switch is unplugged B. The switch loses power C. The switch is rebooted D. The switch floods broadcast communication E. The switch receives an Address Resolution Protocol or ARP request https://www.learncisco.net/courses/icnd-1/ethernet-lans/developing-design-for-layer-2.html A _________ is a virtual instance of a traditional networking device that a consumer can use in a cloud. A. virtual network function B. virtual network appliance C. network virtualized element D. network cloud device What is the name of the protocol that is used by IEEE 802.1x devices to communicate with the authenticator and authentication server? A. EAP B. EAPoL C. RADIUS D. TACACS+ What is known as “one-to-nearest“ addressing in IPv6? A. global unicast B. anycast C. multicast D. unspecified address https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-address-types.html What is the best definition of a WAN? A. Remote access to resources across a high speed link B. Local access to resources C. Local Internet access D. Core network resources Which of the following is required when configuring port security with sticky learning? A. Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand B. Enabling port security with the switchport port-security interface subcommand C. Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand D. All the other answers list required commands Refer to the diagram. What is the official name of the network (Network A) that is broadcast by an AP? A. SSID B. BSS C. ESS D. SRDID You are troubleshooting DNS and want to use a static mapping locally as part of your test. In Windows, in which file can you specify the name for an IPv6 mapping? A. Hosts B. lmhosts C. IPv6hosts D. Addresses Which shorthand notations can be applied to IPv6 addresses? (Choose three) A. An unspecified address is written as a double colon followed by four zeros B. Leading zeros in a field are optional C. Format is x:x:x:x:x:x:x:x, where x is a 16-bit hexadecimal field D. Successive fields of 0 are represented as "::" but only once in an address E. Hexadecimal digits A-F are case sensitive https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-address-types.html A user is experiencing a loss of end-to-end connectivity in an IPv4 network. You have verified that the name resolution entry is correct. Now you want to check whether any IP ACLs are set on the interface. Which command should you use to do so? A. show ip access-list B. show traceroute C. show ip route D. show ip interfaces https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/acl-issues.html You have just configured the following banner on your Cisco IOS router. Router(config)#banner login #This is a secured environment. If you are not authorized to be here, log out immediately.# When will this banner be displayed? A. When the router first boots B. When users are prompted for authentication credentials C. Every 5 minutes by default D. Immediately when any user connects to the device E. Every 10 minutes by default Using the exhibit as a reference, what is a valid key? A. ”lastUpdateTime”: 1572317520439 B. ”CSR1000V” C. ”role” D. ”platformId”: You are setting up a Cisco IOS router as a DHCP server. Which command is used to identify the IPv4 address that is used as the default gateway for the LAN? A. dns-server B. default-gateway C. ip dhcp excluded-address D. ip dhcp pool E. default-router F. domain-name G. network Which cloud service is specific to one company that owns both the tools/infrastructure that creates the cloud and the people that use the services? A. Hybrid cloud B. Public cloud C. Private cloud D. Internal cloud What is the Administrative Distance of internal EIGRP routes? B. 170 C. 90 D. 20 E. 1 F. 110 G. 120 Refer to the diagram. What method of authentication is being used? A. Open authentication B. CCMP C. WEP D. 802.1x Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 Which statements correctly define unique local unicast addresses? (Choose two) A. They are not routable B. They are identified by the prefix FE80::/10 C. They are identified by the prefix 2000::/3 D. They are identified by the prefix FC00::/7 E. They are routable in your private network F. They are globally routable Which statements are true about telnet and ssh? (Choose two) A. Only data traffic is encrypted with ssh B. All telnet traffic is sent in plain text C. All ssh traffic is encrypted D. The data is hashed by telnet during transmission E. The username and password is hashed by telnet during authentication F. Only authentication traffic is encrypted with ssh A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation? A. application B. presentation C. session D. transport E. internet F. data link https://www.learncisco.net/courses/ccna/part-1-internetworking/the-osi-reference-model.html When comparing next-generation IPS to traditional IPS, what additional capabilities can be leveraged to more efficiently block traffic? (Choose three) A. AVC B. Signature-based filtering C. Contextual awareness D. Event impact level Which QoS feature is typically used outbound to an ISP to reduce the amount of traffic that is dropped by exceeding the purchased rate? A. Traffic shaping B. Traffic policing C. Traffic limiting D. Traffic classification Choose the correct order from the following steps for a physical Cisco Catalyst switch startup process. 1. Verify the boot sequence. 2. Follow proper procedures of mounting the physical device 3. Ensure the security of all network cable connections 4. Attach the power cable plug to the switch`s power supply 5. Check the requirements for power and environmental conditions A. 1, 2, 3, 4, 5 B. 3, 4, 2, 1, 5 C. 5, 3, 1, 2, 4 D. 5, 2, 3, 4, 1 E. 4, 1, 2, 5, 3 https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html What information is returned from the “show spanning-tree vlan vlan_id“ command? (Choose three) A. Interface, role, and cost information B. Root ID information C. Number of switches on the network D. Bridge ID information E. Routing protocol Refer to the diagram. What is the name of the device referenced with the arrow, assuming the traffic coming from the wireless clients followed the dashed path? A. Autonomous AP B. Wireless controller C. Lightweight AP D. Wireless router What are the correct pinouts for a crossover cable? (Choose two) A. Pin 2 to pin 3 B. Pin 1 to pin 3 C. Pin 1 to pin 6 D. Pin 2 to pin 6 E. Pin 4 to pin 8 __________ means that the QoS tool changes one or more header fields, setting a value in the header. A. Marking B. Classifying C. Insertion D. Qualifying Which Cisco IOS command is used to advertise a default route into an OSPF domain regardless of whether a default static route is configured? A. default-information originate B. default-information originate always C. default-information originate permanent D. default-information originate no-check If you want to be alerted when a device configuration differs from the intended configuration, what should you implement? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring When a subnet mask is presented in binary, what do the binary 1s represent? A. The network portion of an associated address B. The host portion of the subnet mask C. The number of wildcard bits in the subnet mask D. The number of wildcard bits in the address E. The network portion of the subnet mask F. The host portion of an associated address Which IOS command always displays OSPF hello timer settings? A. show ip protocols B. show ip route C. show ip ospf interface D. show ip ospf neighbor E. debug ip ospf events Why doesn't increasing the number of uplinks solve congestion issues from multiple links aggregating on a switch? A. All traffic must pass through one physical link B. Multiple links require extra overhead C. All uplinks must be running at the same speed D. STP disables ports to prevent loops You are implementing a VLSM network. You are using the Class B network of 172.16.0.0/16 and need to create 256 networks from this. The fifth network will then be subnetted into /30 networks. What is the subnet ID of the fourth /30 network? A. 172.16.4.12/30 B. 172.16.4.4/30 C. 172.16.4.6/30 D. 172.16.4.8/30 E. 172.16.4.14/30 F. 172.16.4.10/30 You have implemented DAI on a Layer 2 switch in your network. Now you want to monitor the ARP message rates with an average of four received ARP messages a second. Which command(s) would need to be utilized to accomplish this? (Choose two) A. ip arp inspection limit rate 8 burst interval 2 B. ip arp inspection limit rate 4 burst interval 2 C. ip arp inspection limit rate 10 burst interval 5 D. ip arp inspection limit rate 20 burst interval 5 Which command could you enter to encrypt passwords? A. enable secret B. username {username} secret {password} C. service password-encryption D. All of the above E. None of the above When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected? A. Passive B. Desirable C. On D. Auto E. Active

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources